fixthiserror_

GAGGENAU E0100

Gaggenau Dishwasher Error Code E0100: Heat Pump Motor Circuit Fault (Extended Code)

Clear meaning, realistic next steps, and safe guidance without turning the page into a long repair manual.

What it means

There is a heat pump motor circuit fault at the main control board.

Severity

High - stop using the Gaggenau dishwasher until the cause is understood or professional help is arranged.

Can you fix it yourself?

No — call a technician

Most likely cause

Same as E01 — heat pump motor circuit fault on newer Gaggenau models

Estimated time for safe first checks: Professional service required.

Step-by-Step DIY Fix Guide

  1. SAFETY: Disconnect power at the breaker.
  2. Reset power for 30 seconds, then restore.
  3. If E0100 returns, call a Gaggenau-certified technician — same repair path as E01.

If the warning comes back after restart

  • If airflow still seems weak after the basic checks, the fan path or a deeper obstruction becomes more likely.
  • If the warning returns immediately after a clean restart, the sensor or wiring path becomes more likely than a one-time glitch.
  • Any recurrence — same repair path as E01

What This Error Means

Error code E0100 on your Gaggenau dishwasher indicates: There is a heat pump motor circuit fault at the main control board. The appliance detects this condition through its built-in sensors and halts the current cycle to prevent further damage. Depending on the model, the code may flash on the display panel, appear on a digital readout, or cause the status lights to blink in a specific sequence. The dishwasher will not resume normal operation until the underlying fault is resolved.

The most frequent cause of error E0100 is same as e01 — heat pump motor circuit fault on newer bosch models. When this happens, the dishwasher's control board detects the abnormal sensor reading or motor response and triggers the fault code as a protective measure. Other contributing factors are listed in the causes section below — working through them in order is the fastest path to a fix.

Gaggenau's official service guidance classifies E0100 as a technician-only repair. The components involved are part of the sealed electronics system and require specialized diagnostic equipment to test safely. Attempting to disassemble these components yourself risks further damage and may void any remaining warranty. Contact Gaggenau Customer Service or a certified appliance technician.

The most visible symptom of E0100 is standing water at the bottom of the tub at the end of a cycle — the dishwasher failed to pump it out. The water may appear cloudy from food particles or detergent residue. Do not run another cycle until the fault is cleared, as this could allow water to overflow onto the floor.

Most Likely Cause by Symptom

The Gaggenau dishwasher may stop, pause, or refuse to complete the cycle normally.

Likely cause: Same as E01 — heat pump motor circuit fault on newer Gaggenau models

Check first: SAFETY: Disconnect power at the breaker.

The warning may return immediately because the appliance is detecting an internal fault.

Likely cause: Same as E01 — heat pump motor circuit fault on newer Gaggenau models

Check first: Reset power for 30 seconds, then restore.

Common Causes

  • Same as E01 — heat pump motor circuit fault on newer Gaggenau models

What Not to Do

  • Do not attempt to disassemble internal electronics or sealed system components
  • Do not bypass or ignore this error and continue running cycles

Model and Display Variation Notes

Model-family notes

  • Gaggenau dishwasher display wording and code formats can vary by series.
  • If your model behaves differently, check the owner manual before trying any deeper maintenance step.

Display and panel differences

  • Panel wording can vary by series, so confirm the exact code pattern before buying parts.

Parts, Tools and Service Options

Service option

Gaggenau service visit if the warning returns after the basic checks are complete.

Manual and model check

Check your exact model and manual before ordering any Gaggenau dishwasher parts.

Common parts

  • Heat pump motor assembly ($150–$350)
  • Main control board ($180–$320)

This section stays service-first because the page points more strongly toward support or professional repair than a routine parts purchase.

When Not to Keep Troubleshooting

Any recurrence — same repair path as E01

How to Prevent It Recurring

  • Descale monthly to protect the heat pump motor

Related Error Codes

Extra notes

  • This page is based on Gaggenau support material and stays conservative where model-specific guidance may vary.
  • The goal is to help you identify safe first checks before you move into parts, service, or model-specific manual lookup.

Source and model notes

Last reviewed: 2026-04-09

Based on: Based on Gaggenau support material and edited into consumer-safe guidance for the exact code family on this page.

View Gaggenau US Support

Model coverage note: Gaggenau dishwasher code meanings can vary by series, control panel, and model family, so use this page as a safe starting point rather than a replacement for the model-specific manual.

Important: FixThisError is an independent guide, not the manufacturer. Use your model-specific manual when the panel wording or behavior differs.

Always disconnect power before inspecting appliances. If unsure, contact a licensed appliance technician.