Step-by-Step DIY Fix Guide
- SAFETY: Disconnect power before inspecting this appliance.
- Open the dispenser drawer and inspect the Load & Go cartridge bay.
- Remove the cartridge and check the fill level — if empty, refill or replace with a new cartridge.
- Reinsert the cartridge firmly until it clicks into place.
- Close the dispenser drawer completely and restart the cycle.
- If dET persists with a confirmed full cartridge properly seated, clean the cartridge bay contacts with a dry cloth.
- If the error continues, run a cycle using the single-dose dispenser compartment as a temporary workaround while you troubleshoot the auto-dispenser.
If the code comes back
- dET persists with a full, correctly seated cartridge after cleaning the bay
What This Error Means
Error dET on your Maytag washing machine means: The washer expected to find a detergent cartridge in the dispenser but could not detect one. This code appears on models with an automatic detergent dispensing system (such as the Load & Go dispenser). The washer will not start the cycle until the cartridge issue is resolved. The washer's self-diagnostic system has detected this condition and paused the current cycle.
The most frequent cause is detergent cartridge not inserted — the load & go cartridge bay is empty. Work through the causes and fix steps below in order — most Maytag washer errors are resolved without a service call.
Error dET is DIY-safe. No tools are required and the fix typically takes under 15 minutes. Follow all steps in sequence.
The Maytag washing machine is a high-efficiency (HE) appliance that uses significantly less water than older top-loaders. Standard (non-HE) detergent produces four to five times more suds than the machine can clear — always use HE-labeled detergent and follow the dosing instructions on the label precisely.
Most Likely Cause by Symptom
The Maytag washing machine may stop, pause, or refuse to complete the cycle normally.
Likely cause: Detergent cartridge not inserted — the Load & Go cartridge bay is empty
Check first: SAFETY: Disconnect power before inspecting this appliance.
Common Causes
- Detergent cartridge not inserted — the Load & Go cartridge bay is empty
- Cartridge not fully seated — the cartridge is present but the detection tab has not engaged
- Empty cartridge — the detergent has run out and the cartridge is not registering as full
- Cartridge detection sensor dirty or faulty
What Not to Do
- Do not force the cartridge bay closed if the cartridge is not fully inserted — forcing it can damage the detection tab
Model and Display Variation Notes
Model-family notes
- Maytag washing machine display wording and code formats can vary by series.
- If your model behaves differently, check the owner manual before trying any deeper maintenance step.
Display and panel differences
- Panel wording can vary by series, so confirm the exact code pattern before buying parts.
Parts, Tools and Service Options
Common parts
- Dispenser cartridge sensor if detection fails consistently ($20–$45)
Manual and model check
Check your exact model and manual before ordering any Maytag washing machine parts.
Suggestions in this section are organized to support the troubleshooting flow first. Any future affiliate relationships should be disclosed clearly.
When Not to Keep Troubleshooting
dET persists with a full, correctly seated cartridge after cleaning the bay
How to Prevent It Recurring
- Check the cartridge fill level every 20–30 loads — refilling before the cartridge empties completely prevents unexpected dET interruptions mid-cycle
Related Error Codes
F8E2
The washer cannot dispense detergent or fabric softener correctly. The dispenser motor or the mechanism that routes water through the detergent compartments has failed or is obstructed.
Sud
The washer has detected an abnormal amount of suds in the drum. Excess suds prevent proper rinsing and can overflow into the pump and motor. The machine will pause and run extra rinse cycles to clear the foam before continuing.
Extra notes
- This page is based on Maytag support material and stays conservative where model-specific guidance may vary.
- The goal is to help you identify safe first checks before you move into parts, service, or model-specific manual lookup.
Source and model notes
Last reviewed: 2026-04-08
Based on: Based on Maytag support material and edited into consumer-safe guidance for the exact code family on this page.
View Maytag US Official Support
Model coverage note: Maytag washing machine code meanings can vary by series, control panel, and model family, so use this page as a safe starting point rather than a replacement for the model-specific manual.
Important: FixThisError is an independent guide, not the manufacturer. Use your model-specific manual when the panel wording or behavior differs.
Always disconnect power before inspecting appliances. If unsure, contact a licensed appliance technician.