fixthiserror_

Full Error Code List

Miele dishwasher error codes

Use this page when you already know the display code or want to compare Miele dishwasher meanings quickly by severity.

How to use this list

Use the table to confirm the exact code, then open the detail guide for the safest first checks, model notes, and next-step options.

What the list is best for

  • Matching the exact display code before you act.
  • Comparing severity and meaning side by side.
  • Spotting closely related warnings that users often confuse.

What happens on the detail page

  • Quick answer and severity guidance.
  • Symptom-based first checks where the content supports it.
  • Model and display notes plus trust and source context.

Miele dishwasher code table

Scan by code, meaning, and severity, then open the exact detail page when you need step-by-step guidance.

F01
The dishwasher has detected a short-circuit in the NTC water temperature sensor. Heating has been deactivated and rinse aid dispensing may be affected. The machine cannot confirm water temperature and has stopped the cycle.
medium severity
F11
The dishwasher is unable to drain water from the wash cabinet. Water is still present in the tub at the end of a drain cycle. This applies to Miele G 1xxx through G 6xxx series models.
medium severity
F12
The dishwasher failed to fill with water at the beginning of a program step. The machine did not detect sufficient water entering the tub within the expected time.
medium severity
F13
The dishwasher's water inlet valve has been identified as defective. The valve is not opening or closing correctly, preventing the dishwasher from filling normally.
high severity
F14
The dishwasher has detected a fault with the heater pressure switch. This switch monitors water level in relation to the heating element, and a fault here prevents safe heating operation.
medium severity
F18
The dishwasher's flow meter is reading zero or near-zero water flow when the machine expects water to be entering. The machine has stopped because it cannot confirm water is reaching the wash system.
medium severity
F24
The dishwasher has detected a malfunction in the circulation pump or a fault in the heater relay on the control board. The circulation pump moves water through the spray arms during the wash cycle — if it fails, dishes will not be washed.
high severity
F78
The dishwasher has detected a circulation pump fault. On first use or after a long period without use, this can occur if the pump ran dry. On established units it indicates a pump obstruction or motor issue.
medium severity
F600
The dishwasher has detected a fault with the AutoDos automatic detergent dispensing system. The drain pump activates and the wash program is cancelled when this code appears. AutoDos is Miele's built-in automatic powder detergent system.
low severity

Common symptom shortcuts

These clusters give users another way into the list when they know the symptom but not the code.

Drain and standing water problems

  • F11 - The dishwasher is unable to drain water from the wash cabinet. Water is still present in the tub at the end of a drain cycle. This applies to Miele G 1xxx through G 6xxx series models.
  • F600 - The dishwasher has detected a fault with the AutoDos automatic detergent dispensing system. The drain pump activates and the wash program is cancelled when this code appears. AutoDos is Miele's built-in automatic powder detergent system.

Leaks, fill, and water-path issues

  • F01 - The dishwasher has detected a short-circuit in the NTC water temperature sensor. Heating has been deactivated and rinse aid dispensing may be affected. The machine cannot confirm water temperature and has stopped the cycle.
  • F11 - The dishwasher is unable to drain water from the wash cabinet. Water is still present in the tub at the end of a drain cycle. This applies to Miele G 1xxx through G 6xxx series models.
  • F12 - The dishwasher failed to fill with water at the beginning of a program step. The machine did not detect sufficient water entering the tub within the expected time.

Sensor and temperature faults

  • F01 - The dishwasher has detected a short-circuit in the NTC water temperature sensor. Heating has been deactivated and rinse aid dispensing may be affected. The machine cannot confirm water temperature and has stopped the cycle.

Common guides to open next

F01 fix guide

F01 - The dishwasher has detected a short-circuit in the NTC water temperature sensor. Heating has been deactivated and rinse aid dispensing may be affected. The machine cannot confirm water temperature and has stopped the cycle.

F11 fix guide

F11 - The dishwasher is unable to drain water from the wash cabinet. Water is still present in the tub at the end of a drain cycle. This applies to Miele G 1xxx through G 6xxx series models.

F12 fix guide

F12 - The dishwasher failed to fill with water at the beginning of a program step. The machine did not detect sufficient water entering the tub within the expected time.

F13 fix guide

F13 - The dishwasher's water inlet valve has been identified as defective. The valve is not opening or closing correctly, preventing the dishwasher from filling normally.