Samsung dryer
Samsung dryer error codes
Browse Samsung dryer error codes with practical explanations for airflow, sensor, heating, and setup-related warnings.
Errors
12
High severity
3
Browse all 12 dryer codes
See the full Samsung dryer error code list with code, meaning, severity, and direct links to the detail pages.
Common Samsung dryer codes
3C
Samsung Dryer Error 3C: Motor Error or Dry Time Error
The dryer has detected a fault with the drum drive motor (3C) or the drying cycle has exceeded the maximum allowed time without reaching the target dryness level (oD).
Open 3C guide
9C1
Samsung Dryer Error 9C1: Voltage Error — Irregular Power Supply
The dryer has detected an abnormality in the voltage being supplied. The power is either too high, too low, or fluctuating beyond safe operating limits.
Open 9C1 guide
AC
Samsung Dryer Error AC: Communication Error — Internal Components
The dryer's internal electronic components cannot communicate with each other. A communication breakdown has occurred between the main control board and one or more subsystems.
Open AC guide
bE
Samsung Dryer Error bE: Jammed Button — Control Panel Key Stuck
The dryer's control panel has detected that one or more buttons are stuck in a continuously pressed state, preventing normal operation.
Open bE guide
CL
Samsung Dryer Error CL: Child Lock Active
The child safety lock is engaged. All control panel buttons are disabled and on some models the door is also locked. This is a safety mode, not a fault.
Open CL guide
Clg
Samsung Dryer Error Clg: Dryer Vent Is Clogged
Samsung dryer error Clg usually means the exhaust vent is heavily restricted and airflow is no longer safe.
Open Clg guide
Symptom entry points
Drain and standing water problems
- bE - The dryer's control panel has detected that one or more buttons are stuck in a continuously pressed state, preventing normal operation.
- Clg - Samsung dryer error Clg usually means the exhaust vent is heavily restricted and airflow is no longer safe.
- HC - Samsung dryer error HC usually means the dryer is overheating and has shut heating down to prevent damage or fire risk.
Door, latch, and lock warnings
- CL - The child safety lock is engaged. All control panel buttons are disabled and on some models the door is also locked. This is a safety mode, not a fault.
- dC - The dryer cannot detect that the door is properly closed and latched. The cycle will not start or has been interrupted because the door lock cannot confirm a secure position.
Sensor and temperature faults
- 3C - The dryer has detected a fault with the drum drive motor (3C) or the drying cycle has exceeded the maximum allowed time without reaching the target dryness level (oD).
- dC - The dryer cannot detect that the door is properly closed and latched. The cycle will not start or has been interrupted because the door lock cannot confirm a secure position.
- HC2 - The gas dryer has detected a failure in the gas ignition system. The burner is not lighting correctly or at all, preventing the dryer from generating heat.
Model-family guidance
What can vary by model
- Samsung dryer display wording and code formats can vary by series.
- If your model behaves differently, check the owner manual before trying any deeper maintenance step.
- Some models may display the same fault as 3C, oD.
- Some models may display the same fault as 9C1, 9E, 2E, 9E1.
Frequently asked questions
Appliance-level FAQs add supporting context without forcing users into long-form content.
Where should I start with Samsung dryer error codes?
Start with the dryer overview page, then use the full error code list or open the code that matches your display. Each page gives a quick meaning, safe checks, and escalation guidance.
Are all Samsung dryer codes the same across models?
Not always. Meanings can vary by series or model, so the guidance here stays conservative and recommends checking the manual for model-specific wording.
When should I stop troubleshooting and contact support?
If the same warning returns, the appliance is leaking, will not run safely, or the next step would require invasive work, it is best to turn it off and contact Samsung support or a qualified technician.
Which dryer codes are covered in this section?
This Samsung dryer section currently includes 3C, 9C1, AC, bE, CL, Clg, dC, dn, FC, HC, HC2, tC and related variants based on the current content set.